Fiducial Application Guide

  • Applying Club Markers

    In order to capture club data with the GCQuad, club markers must be applied to the clubface. To apply markers using the dispenser (included):

    • Instruction Guide

      STEP 1

      Clean the clubface with an alcohol pad or water.

      applying club markers 1

      STEP 2

      Turn the wheel clockwise to dispense a club marker.

      applying club markers 2

      STEP 3

      Place club marker at the desired location on the clubface, adhesive side down. See images for correct fiducial placement.

      applying club markers 1

      Step 4

      Firmly apply pressure to the marker with your finger and gently pull the tab away, leaving only the marker on the clubface.

      applying club markers 4
    • Data Captured

      applying club markers 2

      4 MARKERS

      • CLUBHEAD SPEED
      • SMASH FACTOR
      • ATTACK ANGLE
      • SWING PATH
      • FACE ANGLE
      • LOFT
      • LIE
      applying club markers 2

      1 MARKER

      • CLUBHEAD SPEED
      • SMASH FACTOR
      • ATTACK ANGLE
      • SWING PATH
  • Single Marker Placement

    For best results, place the marker high on the clubface and as close to the horizontal center as possible.

    • DRIVERS FAIRWAYS & HYBRIDS

      Single Marker Placement

      IRONS & PUTTERS

      Irons and putters
  • Four Marker Placement

    • Irons

      Step 1

      Step 1

      From the bottom of the club, count score lines up to find the approximate vertical hitting center.

      Step 2

      Step 2

      Carefully apply the first two markers between the sixth and seventh score lines at the toe and heel, keeping both markers level with each other. Place marker about 1 marker width from the edge of the score line. The center point between these two markers will define the horizontal center of the face.

      Step 3

      Step 3

      Carefully apply the last two markers on the toe of the club face at the top and bottom edges of the ball strike zone.

    • Drivers

      Step 1 of Driver Fiducial Placement

      Step 1

      Count the club’s score lines to determine the vertical center of the clubface. Note: For clubs with an even number of score lines, the vertical face center will be between the center two score lines. For clubs with an odd number of score lines, the vertical face center will be directly on the center score line.

      Step 2 of Driver Fiducial Placement

      Step 2

      Carefully apply the first two markers along the vertical center of the face near the outer edge of the score lines, keeping both markers level with each other. The center point between these two markers will define the horizontal center of the face.

      Step 3 of Driver Fiducial Placement

      Step 3

      Carefully apply the last two markers on the toe of the club face at the top and bottom edges of the ball strike zone.

  • Data Captured

    • 1 MARKER

      1 marker

       

      • CLUBHEAD SPEED
      • SMASH FACTOR
      • ANGLE OF ATTACK
      • CLUB PATH

       

      2 MARKERS

      2 markers

       

      • CLUBHEAD SPEED
      • SMASH FACTOR
      • ANGLE OF ATTACK
      • CLUB PATH
      • IMPACT LIE
      • CLUB PATH

      3 MARKERS

      3 MARKERS

       

      • CLUBHEAD SPEED
      • SMASH FACTOR
      • ANGLE OF ATTACK
      • CLUB PATH
      • IMPACT LOCATION
      • IMPACT LIE
      • CLUB PATH

       

  • Dot Placement for Putting

    • 1 DOT

      1 dot

      For best results, place the marker high on the clubface and as close to the horizontal center as possible.

      2 DOT

      2 dot

      The fiducials should be placed along the vertical center line, at the edges of the club face, and be equidistant from the horizontal center line of the club face..

      3 DOT

      3 dot

      The heel fiducial should be placed along the vertical center line, at the heel edge of the club face. The two remaining fiducials should be placed the same dis-tance from the horizontal center as the first, on the opposite (toe) edge. The 2 toe fiducials should be placed equidistant from the vertical center line.